SPEC CPU®2017 Floating Point Rate Result

Copyright 2017-2019 Standard Performance Evaluation Corporation

Hewlett Packard Enterprise (Test Sponsor: HPE)

ProLiant DL325 Gen10
(2.00 GHz, AMD EPYC 7702P)

SPECrate®2017_fp_base = 24800

SPECrate®2017_fp_energy_base = 72100

SPECrate®2017_fp_peak = 27300

SPECrate®2017_fp_energy_peak = 78500
CPU2017 License: 003 Test Date: Aug-2019
Test Sponsor: HPE Hardware Availability: Oct-2019
Tested by: HPE Software Availability: Aug-2019

Benchmark result graphs are available in the PDF report.

Hardware
CPU Name: AMD EPYC 7702P
  Max MHz: 3350
  Nominal: 2000
Enabled: 64 cores, 1 chip, 2 threads/core
Orderable: 1 chip
Cache L1: 32 KB I + 32 KB D on chip per core
  L2: 512 KB I+D on chip per core
  L3: 256 MB I+D on chip per chip,
16 MB shared / 4 cores
  Other: None
Memory: 256 GB (8 x 32 GB 2Rx4 PC4-2933Y-L)
Storage: 1 x HPE 480 GB SATA 6G SSD
Other: None
Software
OS: SUSE Linux Enterprise Server 15 (x86_64) SP1
Kernel 4.12.14-195-default
Compiler: C/C++/Fortran: Version 2.0.0 of AOCC
Parallel: No
Firmware: HPE BIOS Version A41 07/20/2019 released Aug-2019
File System: btrfs
System State: Run level 3 (multi-user)
Base Pointers: 64-bit
Peak Pointers: 64-bit
Other: jemalloc: jemalloc memory allocator library v5.2.0
Power Management: Disabled
Power
Max. Power (W): 411.98
Idle Power (W): 191.52
Min. Temperature (C): 20.63
Elevation (m): 132
Line Standard: 208 V / 60 Hz / 1 phase / 2 wires
Provisioning: Line-powered
Power Settings
Management FW: Version 1.43 of iLO5 released May 23 2019
Memory Mode: Normal
Power-Relevant Hardware
Power Supply: 1 x 800 W (non-redundant)
  Details: HPE 800W Flex Slot Titanium Hot Plug Low Halogen
Power Supply Kit (865438-B21)
Backplane: 8 SFF NVMe with optional optical drive
Other Storage: Embedded SATA Controller
Storage Model #s: P05976-B21
NICs Installed: 1 x HPE Ethernet 4-port 331i Adapter @ 1 Gb
NICs Enabled (FW/OS): 4 / 4
NICs Connected/Speed: 2 @ 1 Gb
Other HW Model #s: 7 x High Performance fans
Power Analyzer
Power Analyzer: 10.216.1.15:8888
Hardware Vendor: Yokogawa
Model: YokogawaWT210
Serial Number: 91K308562
Input Connection: GPIB via NI GIPB-USB-HS
Metrology Institute: NIST
Calibration By: TRANSCAT
Calibration Label: 5-E553M-20-1
Calibration Date: 21-May-2019
PTDaemon™ Version: 1.9.1 (a2d19f26; 2019-07-17)
Setup Description: SUT Power Supply 1 via neoXt NXB 20815
Current Ranges Used: 1A, 2A
Voltage Range Used: 300V
Temperature Meter
Temperature Meter: 10.216.1.15:8889
Hardware Vendor: Digi International Inc.
Model: DigiWATCHPORT_H
Serial Number: V45297862
Input Connection: USB
PTDaemon Version: 1.9.1 (a2d19f26; 2019-07-17)
Setup Description: 5 mm in front of SUT main intake

Base Results Table

Benchmark Copies Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power
SPECrate®2017_fp_base 24800
SPECrate®2017_fp_energy_base 72100
Results appear in the order in which they were run. Bold underlined text indicates a median measurement.
503.bwaves_r 64 1914 3350 7680 911 401 404 1914 3350 7680 911 401 405 1914 3350 7680 911 401 405
507.cactuBSSN_r 64 242 3350 97.6 913 403 406 242 3350 97.7 912 403 406 242 3350 97.6 913 403 406
508.namd_r 64 267 2280 95.8 691 359 367 263 2310 95.4 695 362 367 266 2290 95.6 693 360 368
510.parest_r 64 769 2180 2900 627 378 385 770 2180 2910 627 378 385 774 2160 2920 623 378 385
511.povray_r 64 432 3460 1480 1090 343 347 435 3430 1490 1090 342 346 432 3460 1490 1090 344 347
519.lbm_r 64 803 84.0 3290 233 410 412 803 84.0 3290 233 410 412 803 84.0 3300 232 411 412
521.wrf_r 64 617 2320 2450 638 398 403 617 2330 2460 637 399 405 619 2320 2470 635 398 404
526.blender_r 64 313 3110 1140 925 364 393 313 3110 1140 925 364 393 313 3120 1140 928 364 393
527.cam4_r 64 372 3010 1420 861 380 403 374 2990 1420 857 381 403 374 2990 1420 857 381 403
538.imagick_r 64 208 7650 65.1 2650 313 383 203 7830 64.1 2690 315 378 203 7850 63.8 2700 315 383
544.nab_r 64 248 4350 90.3 1290 365 378 249 4330 90.7 1290 364 378 247 4350 90.3 1290 365 378
549.fotonik3d_r 64 2174 1150 8490 327 390 393 2173 1150 8480 328 390 393 2173 1150 8480 328 390 393
554.roms_r 64 1032 98.5 4170 269 404 407 1034 98.4 4180 268 404 407 1032 98.6 4170 269 404 407

Peak Results Table

Benchmark Copies Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power
SPECrate®2017_fp_peak 27300
SPECrate®2017_fp_energy_peak 78500
Results appear in the order in which they were run. Bold underlined text indicates a median measurement.
503.bwaves_r 32 911 3520 3400 1030 373 376 911 3520 3400 1030 373 376 911 3520 3400 1030 373 376
507.cactuBSSN_r 64 242 3350 97.6 913 403 406 242 3350 97.7 912 403 406 242 3350 97.6 913 403 406
508.namd_r 128 464 2620 1760 755 379 385 464 2620 1760 755 379 385 464 2620 1750 756 378 386
510.parest_r 64 769 2180 2900 627 378 385 770 2180 2910 627 378 385 774 2160 2920 623 378 385
511.povray_r 128 714 4190 2560 1270 358 363 715 4180 2560 1270 358 362 715 4180 2560 1270 358 362
519.lbm_r 64 803 84.0 3290 233 410 412 803 84.0 3290 233 410 412 803 84.0 3300 232 411 412
521.wrf_r 64 617 2320 2450 638 398 403 617 2330 2460 637 399 405 619 2320 2470 635 398 404
526.blender_r 128 533 3660 2050 1030 385 403 535 3650 2060 1030 385 403 535 3640 2060 1020 385 403
527.cam4_r 64 374 3000 1420 857 381 407 373 3000 1420 857 381 400 375 2980 1430 853 381 405
538.imagick_r 128 291 11000 1030 3360 353 401 291 11000 1030 3360 353 401 291 10900 1030 3350 353 400
544.nab_r 128 410 5250 1550 1510 378 385 411 5250 1550 1510 378 382 411 5240 1550 1500 378 385
549.fotonik3d_r 32 1064 1170 3790 366 356 359 1065 1170 3790 366 356 359 1065 1170 3790 366 356 359
554.roms_r 32 443 1150 1750 320 396 401 449 1130 1770 317 394 400 446 1140 1760 318 396 401

Compiler Notes

The AMD64 AOCC Compiler Suite is available at
http://developer.amd.com/amd-aocc/

Submit Notes

The config file option 'submit' was used.
'numactl' was used to bind copies to the cores.
See the configuration file for details.

Operating System Notes

'ulimit -s unlimited' was used to set environment stack size
'ulimit -l 2097152' was used to set environment locked pages in memory limit

runcpu command invoked through numactl i.e.:
numactl --interleave=all runcpu <etc>

Set dirty_ratio=8 to limit dirty cache to 8% of memory
Set swappiness=1 to swap only if necessary
Set zone_reclaim_mode=1 to free local node memory and avoid remote memory
sync then drop_caches=3 to reset caches before invoking runcpu

dirty_ratio, swappiness, zone_reclaim_mode and drop_caches were
all set using privileged echo (e.g. echo 1 > /proc/sys/vm/swappiness).

Transparent huge pages set to 'always' for this run (OS default)

Environment Variables Notes

Environment variables set by runcpu before the start of the run:
LD_LIBRARY_PATH =
     "/cpu2017/amd_rate_aocc200_rome_C_lib/64;/cpu2017/amd_rate_aocc200_rome_
     C_lib/32:"
MALLOC_CONF = "retain:true"

General Notes

Binaries were compiled on a system with 2x AMD EPYC 7601 CPU + 512GB Memory using Fedora 26

NA: The test sponsor attests, as of date of publication, that CVE-2017-5754 (Meltdown)
is mitigated in the system as tested and documented.
Yes: The test sponsor attests, as of date of publication, that CVE-2017-5753 (Spectre variant 1)
is mitigated in the system as tested and documented.
Yes: The test sponsor attests, as of date of publication, that CVE-2017-5715 (Spectre variant 2)
is mitigated in the system as tested and documented.

jemalloc: configured and built with GCC v9.1.0 in Ubuntu 19.04 with -O3 -znver2 -flto
jemalloc 5.2.0 is available here:
https://github.com/jemalloc/jemalloc/releases/download/5.2.0/jemalloc-5.2.0.tar.bz2


Submitted_by: "Bucek, James" <[email protected]>
Submitted: Tue Sep 17 00:02:18 EDT 2019
Submission: cpu2017-20190903-17793.sub

Platform Notes

BIOS Configuration:
 Thermal Configuration set to Maximum Cooling
 Determinism Control set to Manual
 Performance Determinism set to Power Deterministic
 Memory Patrol Scrubbing set to Disabled
 NUMA memory domains per socket set to Four memory domains per socket
 Last-Level Cache (LLC) as NUMA Node set to Enabled
 Workload Profile set to General Throughput Compute
 Minimum Processor Idle Power Core C-State set to C6 State

 Sysinfo program /cpu2017/bin/sysinfo
 Rev: r6365 of 2019-08-21 295195f888a3d7edb1e6e46a485a0011
 running on dl325gen10 Fri Aug 30 23:38:11 2019

 SUT (System Under Test) info as seen by some common utilities.
 For more information on this section, see
    https://www.spec.org/cpu2017/Docs/config.html#sysinfo

 From /proc/cpuinfo
    model name : AMD EPYC 7702P 64-Core Processor
       1  "physical id"s (chips)
       128 "processors"
    cores, siblings (Caution: counting these is hw and system dependent. The following
    excerpts from /proc/cpuinfo might not be reliable.  Use with caution.)
       cpu cores : 64
       siblings  : 128
       physical 0: cores 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
       25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
       53 54 55 56 57 58 59 60 61 62 63

 From lscpu:
      Architecture:        x86_64
      CPU op-mode(s):      32-bit, 64-bit
      Byte Order:          Little Endian
      Address sizes:       48 bits physical, 48 bits virtual
      CPU(s):              128
      On-line CPU(s) list: 0-127
      Thread(s) per core:  2
      Core(s) per socket:  64
      Socket(s):           1
      NUMA node(s):        16
      Vendor ID:           AuthenticAMD
      CPU family:          23
      Model:               49
      Model name:          AMD EPYC 7702P 64-Core Processor
      Stepping:            0
      CPU MHz:             2000.000
      CPU max MHz:         2000.0000
      CPU min MHz:         1500.0000
      BogoMIPS:            3992.24
      Virtualization:      AMD-V
      L1d cache:           32K
      L1i cache:           32K
      L2 cache:            512K
      L3 cache:            16384K
      NUMA node0 CPU(s):   0-3,64-67
      NUMA node1 CPU(s):   4-7,68-71
      NUMA node2 CPU(s):   8-11,72-75
      NUMA node3 CPU(s):   12-15,76-79
      NUMA node4 CPU(s):   16-19,80-83
      NUMA node5 CPU(s):   20-23,84-87
      NUMA node6 CPU(s):   24-27,88-91
      NUMA node7 CPU(s):   28-31,92-95
      NUMA node8 CPU(s):   32-35,96-99
      NUMA node9 CPU(s):   36-39,100-103
      NUMA node10 CPU(s):  40-43,104-107
      NUMA node11 CPU(s):  44-47,108-111
      NUMA node12 CPU(s):  48-51,112-115
      NUMA node13 CPU(s):  52-55,116-119
      NUMA node14 CPU(s):  56-59,120-123
      NUMA node15 CPU(s):  60-63,124-127
      Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
      pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm
      constant_tsc rep_good nopl xtopology nonstop_tsc cpuid extd_apicid aperfmperf pni
      pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 movbe popcnt aes xsave avx f16c
      rdrand lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch
      osvw ibs skinit wdt tce topoext perfctr_core perfctr_nb bpext perfctr_l2 mwaitx cpb
      cat_l3 cdp_l3 hw_pstate ssbd ibrs ibpb stibp vmmcall fsgsbase bmi1 avx2 smep bmi2
      cqm rdt_a rdseed adx smap clflushopt clwb sha_ni xsaveopt xsavec xgetbv1 xsaves
      cqm_llc cqm_occup_llc cqm_mbm_total cqm_mbm_local clzero irperf xsaveerptr arat npt
      lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter
      pfthreshold avic v_vmsave_vmload vgif umip rdpid overflow_recov succor smca

 /proc/cpuinfo cache data
    cache size : 512 KB

 From numactl --hardware  WARNING: a numactl 'node' might or might not correspond to a
 physical chip.
   available: 16 nodes (0-15)
   node 0 cpus: 0 1 2 3 64 65 66 67
   node 0 size: 15908 MB
   node 0 free: 15808 MB
   node 1 cpus: 4 5 6 7 68 69 70 71
   node 1 size: 16126 MB
   node 1 free: 16013 MB
   node 2 cpus: 8 9 10 11 72 73 74 75
   node 2 size: 16126 MB
   node 2 free: 16032 MB
   node 3 cpus: 12 13 14 15 76 77 78 79
   node 3 size: 16125 MB
   node 3 free: 16049 MB
   node 4 cpus: 16 17 18 19 80 81 82 83
   node 4 size: 16126 MB
   node 4 free: 16032 MB
   node 5 cpus: 20 21 22 23 84 85 86 87
   node 5 size: 16126 MB
   node 5 free: 16051 MB
   node 6 cpus: 24 25 26 27 88 89 90 91
   node 6 size: 16126 MB
   node 6 free: 16056 MB
   node 7 cpus: 28 29 30 31 92 93 94 95
   node 7 size: 16125 MB
   node 7 free: 16055 MB
   node 8 cpus: 32 33 34 35 96 97 98 99
   node 8 size: 16126 MB
   node 8 free: 16055 MB
   node 9 cpus: 36 37 38 39 100 101 102 103
   node 9 size: 16126 MB
   node 9 free: 16053 MB
   node 10 cpus: 40 41 42 43 104 105 106 107
   node 10 size: 16126 MB
   node 10 free: 16053 MB
   node 11 cpus: 44 45 46 47 108 109 110 111
   node 11 size: 16125 MB
   node 11 free: 16049 MB
   node 12 cpus: 48 49 50 51 112 113 114 115
   node 12 size: 16126 MB
   node 12 free: 16051 MB
   node 13 cpus: 52 53 54 55 116 117 118 119
   node 13 size: 16126 MB
   node 13 free: 16047 MB
   node 14 cpus: 56 57 58 59 120 121 122 123
   node 14 size: 16126 MB
   node 14 free: 16050 MB
   node 15 cpus: 60 61 62 63 124 125 126 127
   node 15 size: 16082 MB
   node 15 free: 16011 MB
   node distances:
   node   0   1   2   3   4   5   6   7   8   9  10  11  12  13  14  15
     0:  10  11  11  11  12  12  12  12  12  12  12  12  12  12  12  12
     1:  11  10  11  11  12  12  12  12  12  12  12  12  12  12  12  12
     2:  11  11  10  11  12  12  12  12  12  12  12  12  12  12  12  12
     3:  11  11  11  10  12  12  12  12  12  12  12  12  12  12  12  12
     4:  12  12  12  12  10  11  11  11  12  12  12  12  12  12  12  12
     5:  12  12  12  12  11  10  11  11  12  12  12  12  12  12  12  12
     6:  12  12  12  12  11  11  10  11  12  12  12  12  12  12  12  12
     7:  12  12  12  12  11  11  11  10  12  12  12  12  12  12  12  12
     8:  12  12  12  12  12  12  12  12  10  11  11  11  12  12  12  12
     9:  12  12  12  12  12  12  12  12  11  10  11  11  12  12  12  12
    10:  12  12  12  12  12  12  12  12  11  11  10  11  12  12  12  12
    11:  12  12  12  12  12  12  12  12  11  11  11  10  12  12  12  12
    12:  12  12  12  12  12  12  12  12  12  12  12  12  10  11  11  11
    13:  12  12  12  12  12  12  12  12  12  12  12  12  11  10  11  11
    14:  12  12  12  12  12  12  12  12  12  12  12  12  11  11  10  11
    15:  12  12  12  12  12  12  12  12  12  12  12  12  11  11  11  10

 From /proc/meminfo
    MemTotal:       263943500 kB
    HugePages_Total:       0
    Hugepagesize:       2048 kB

 From /etc/*release* /etc/*version*
    os-release:
       NAME="SLES"
       VERSION="15-SP1"
       VERSION_ID="15.1"
       PRETTY_NAME="SUSE Linux Enterprise Server 15 SP1"
       ID="sles"
       ID_LIKE="suse"
       ANSI_COLOR="0;32"
       CPE_NAME="cpe:/o:suse:sles:15:sp1"

 uname -a:
    Linux dl325gen10 4.12.14-195-default #1 SMP Tue May 7 10:55:11 UTC 2019 (8fba516)
    x86_64 x86_64 x86_64 GNU/Linux

 Kernel self-reported vulnerability status:

 CVE-2018-3620 (L1 Terminal Fault):        Not affected
 Microarchitectural Data Sampling:         Not affected
 CVE-2017-5754 (Meltdown):                 Not affected
 CVE-2018-3639 (Speculative Store Bypass): Mitigation: Speculative Store Bypass disabled
                                           via prctl and seccomp
 CVE-2017-5753 (Spectre variant 1):        Mitigation: __user pointer sanitization
 CVE-2017-5715 (Spectre variant 2):        Mitigation: Full AMD retpoline, IBPB:
                                           conditional, IBRS_FW, STIBP: conditional, RSB
                                           filling

 run-level 3 Aug 30 17:56

 SPEC is set to: /cpu2017
    Filesystem     Type   Size  Used Avail Use% Mounted on
    /dev/sda2      btrfs   40G   11G   29G  28% /

 From /sys/devices/virtual/dmi/id
     BIOS:    HPE A41 07/20/2019
     Vendor:  HPE
     Product: ProLiant DL325 Gen10
     Product Family: ProLiant
     Serial:  CN781302PS

 Additional information from dmidecode follows.  WARNING: Use caution when you interpret
 this section. The 'dmidecode' program reads system data which is "intended to allow
 hardware to be accurately determined", but the intent may not be met, as there are
 frequent changes to hardware, firmware, and the "DMTF SMBIOS" standard.
   Memory:
     8x UNKNOWN NOT AVAILABLE
     8x UNKNOWN NOT AVAILABLE 32 GB 2 rank 2933

 (End of data from sysinfo program)

Power Settings Notes

PTDaemon to measure power and temperature was run on a ProLiant DL360 Gen9 as a controller
with 2x Intel Xeon E5-2660 v3 CPU and 128 GB of memory using Windows Server 2012 R2.
Power management in the OS was disabled by setting Linux CPU governor to performance for all cores:
 cpupower frequency-set -r -g performance
Power management in the BIOS was default except for any settings mentioned in BIOS Configuration.
No power management settings were set in the management firmware.
The optional optical drive was not installed.
The system was configured with 7 HPE Small Form Factor Hard Drive Blanks (666987-B21), 8 DIMM blanks
2 high performance heatsinks and baffles that fit over the high performance
heatsinks in order to produce correct airflow and cooling.
The run was started and observed through the management firmware.
The Embedded SATA controller was the HPE Smart Array S100i SR Gen10 SW RAID.

Compiler Version Notes

==============================================================================
C               | 519.lbm_r(base, peak) 538.imagick_r(base, peak)
                | 544.nab_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++             | 508.namd_r(base, peak) 510.parest_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++, C          | 511.povray_r(base, peak) 526.blender_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++, C, Fortran | 507.cactuBSSN_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
Fortran         | 503.bwaves_r(base, peak) 549.fotonik3d_r(base, peak)
                | 554.roms_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
Fortran, C      | 521.wrf_r(base, peak) 527.cam4_r(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

Base Compiler Invocation

C benchmarks:

 clang 

C++ benchmarks:

 clang++ 

Fortran benchmarks:

 flang 

Benchmarks using both Fortran and C:

 flang   clang 

Benchmarks using both C and C++:

 clang++   clang 

Benchmarks using Fortran, C, and C++:

 clang++   clang   flang 

Base Portability Flags

503.bwaves_r:  -DSPEC_LP64 
507.cactuBSSN_r:  -DSPEC_LP64 
508.namd_r:  -DSPEC_LP64 
510.parest_r:  -DSPEC_LP64 
511.povray_r:  -DSPEC_LP64 
519.lbm_r:  -DSPEC_LP64 
521.wrf_r:  -DSPEC_CASE_FLAG   -Mbyteswapio   -DSPEC_LP64 
526.blender_r:  -funsigned-char   -D__BOOL_DEFINED   -DSPEC_LP64 
527.cam4_r:  -DSPEC_CASE_FLAG   -DSPEC_LP64 
538.imagick_r:  -DSPEC_LP64 
544.nab_r:  -DSPEC_LP64 
549.fotonik3d_r:  -DSPEC_LP64 
554.roms_r:  -DSPEC_LP64 

Base Optimization Flags

C benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -z muldefs   -lmvec   -lamdlibm   -ljemalloc   -lflang 

C++ benchmarks:

 -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-suppress-fmas   -O3   -ffast-math   -march=znver2   -mllvm -loop-unswitch-threshold=200000   -mllvm -vector-library=LIBMVEC   -mllvm -unroll-threshold=100   -flv-function-specialization   -mllvm -enable-partial-unswitch   -z muldefs   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Fortran benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -march=znver2   -funroll-loops   -Mrecursive   -mllvm -vector-library=LIBMVEC   -z muldefs   -Kieee   -fno-finite-math-only   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using both Fortran and C:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -funroll-loops   -Mrecursive   -z muldefs   -Kieee   -fno-finite-math-only   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using both C and C++:

 -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-suppress-fmas   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -mllvm -loop-unswitch-threshold=200000   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -z muldefs   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using Fortran, C, and C++:

 -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-suppress-fmas   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -mllvm -loop-unswitch-threshold=200000   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -funroll-loops   -Mrecursive   -z muldefs   -Kieee   -fno-finite-math-only   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Peak Compiler Invocation

C benchmarks:

 clang 

C++ benchmarks:

 clang++ 

Fortran benchmarks:

 flang 

Benchmarks using both Fortran and C:

 flang   clang 

Benchmarks using both C and C++:

 clang++   clang 

Benchmarks using Fortran, C, and C++:

 clang++   clang   flang 

Peak Portability Flags

Same as Base Portability Flags

Peak Optimization Flags

C benchmarks:

519.lbm_r:  basepeak = yes 
538.imagick_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -lmvec   -lamdlibm   -ljemalloc   -lflang 
544.nab_r:  Same as 538.imagick_r 

C++ benchmarks:

508.namd_r:  -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -flv-function-specialization   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -mllvm -loop-unswitch-threshold=200000   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -lmvec   -lamdlibm   -ljemalloc   -lflang 
510.parest_r:  basepeak = yes 

Fortran benchmarks:

503.bwaves_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -march=znver2   -funroll-loops   -Mrecursive   -mllvm -vector-library=LIBMVEC   -Kieee   -fno-finite-math-only   -lmvec   -lamdlibm   -ljemalloc   -lflang 
549.fotonik3d_r:  Same as 503.bwaves_r 
554.roms_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-enable-X86-prefetching   -O3   -march=znver2   -funroll-loops   -Mrecursive   -mllvm -vector-library=LIBMVEC   -Kieee   -fno-finite-math-only   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using both Fortran and C:

521.wrf_r:  basepeak = yes 
527.cam4_r:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -O3   -funroll-loops   -Mrecursive   -Kieee   -fno-finite-math-only   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using both C and C++:

511.povray_r:  -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-x86-use-vzeroupper=false   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -mllvm -loop-unswitch-threshold=200000   -lmvec   -lamdlibm   -ljemalloc   -lflang 
526.blender_r:  -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -mllvm -loop-unswitch-threshold=200000   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using Fortran, C, and C++:

507.cactuBSSN_r:  basepeak = yes 

The flags files that were used to format this result can be browsed at
http://www.spec.org/cpu2017/flags/aocc200-flags-B1.html,
http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-V1.2-EPYC-revF.html.

You can also download the XML flags sources by saving the following links:
http://www.spec.org/cpu2017/flags/aocc200-flags-B1.xml,
http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-V1.2-EPYC-revF.xml.

PTDaemon, SPEC CPU, and SPECrate are trademarks or registered trademarks of the Standard Performance Evaluation Corporation. All other brand and product names appearing in this result are trademarks or registered trademarks of their respective holders.

For questions about this result, please contact the tester. For other inquiries, please contact [email protected]
Copyright 2017-2019 Standard Performance Evaluation Corporation
Tested with SPEC CPU®2017 v1.1.0 on 2019-08-31 00:38:10-0400.
Report generated on 2019-09-17 16:19:01 by SPEC CPU®2017 HTML formatter v6255.
Originally published on 2019-09-17.